The effect of floor flexibility on the seismic behaviour of post-tensioned timber buildings

dc.contributor.authorvan Beerschoten, W.
dc.contributor.authorNewcombe, M.P.
dc.date.accessioned2014-10-14T23:00:33Z
dc.date.available2014-10-14T23:00:33Z
dc.date.issued2010en
dc.description.abstractThis report describes in-plane experimental testing and numerical modelling of timberconcrete floor diaphragms. The experimental tests investigated the in-plane stiffness of the diaphragm and the stiffness and strength of different connections between the diaphragm and the lateral load resisting system. The test model was 1/3 scale and three meters square in plan. Seven tests with a different kind of connection between the floor and the rigid lateral supports (which simulated a timber lateral load resisting system) have been performed. The results of the experimental testing are used to calibrate numerical models which are used to investigate the effects of the floor flexibility on the seismic behaviour of post-tensioned timber buildings. For the experimental tests, screw and nail fasteners were used to connected to floor unit to the lateral supports. These fasteners were embedded into the concrete slab or timber edge joints at different orientations. The stiffness of the diaphragm connections was vastly different for each detail. Screws installed at a 45? angle (inclined) to the lateral supports were four times stiffer than the screws installed orthogonal to the lateral supports. The initial stiffness of the inclined fasteners was similar for timber-to-timber and concrete-to-timber connections. For the timberto- timber connections the orientation did not seem to influence the strength of the connection. The tested diaphragm had an uncracked stiffness of 4000 kN/mm and a cracked stiffness of 300 kN/mm. For the tested floor unit it was concluded that the influence of the diaphragm flexibility was negligible compared to the connector flexibility. The floor flexibility can be idealized as three different parts, the deformation of the connectors, the shear deformation of the diaphragm and the flexural deformation of the diaphragm. The numerical analyses showed that in most perceivable situations the connection deformation will govern the in-plane seismic response of the floor. Hence, it is justified to model it as a single-degree-of-freedom (SDOF) element. The influence of the floor flexibility on the seismic response of post-tensioned timber buildings is small. In most cases neglecting the floor flexibility is a conservative approach for the structural design of the building. However, structures with stiff walls and long floor spans there can be a significant amplification of the seismic response. For that case, a simple SDOF representation is proposed. Code-based recommendations for predicting the peak floor accelerations are found to be inadequate. A methodology is proposed to more accurately predict the expected peak floor accelerations for designen
dc.identifier.citationvan Beerschoten, W., Newcombe, M.P. (2010) The effect of floor flexibility on the seismic behaviour of post-tensioned timber buildings. Department of Civil & Natural Resources Engineering University of Canterbury Christchurch, New Zealanden
dc.identifier.urihttp://hdl.handle.net/10092/9688
dc.language.isoen
dc.publisherUniversity of Canterbury Christchurch, New Zealanden
dc.publisherUniversity of Canterbury. Civil and Natural Resources Engineeringen
dc.rights.urihttps://hdl.handle.net/10092/17651en
dc.subject.anzsrcFields of Research::40 - Engineering::4005 - Civil engineering::400506 - Earthquake engineeringen
dc.subject.anzsrcFields of Research::40 - Engineering::4005 - Civil engineering::400510 - Structural engineeringen
dc.titleThe effect of floor flexibility on the seismic behaviour of post-tensioned timber buildingsen
dc.typeReports
Files
Original bundle
Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
12646023_VAN BEERSCHOTEN WOUTER The Effect of Floor Flexibility of the Seismic Behaviour of Post-Tensioned Timber Buildings UoC Research Report 2010.pdf
Size:
4.21 MB
Format:
Adobe Portable Document Format